- #Hard disk serial number changer generator how to
- #Hard disk serial number changer generator mod
- #Hard disk serial number changer generator upgrade
- #Hard disk serial number changer generator plus
- #Hard disk serial number changer generator professional
I did see you asked for someone to do this for you now you are doing it on your own. Not sure it is your drive and your data and you can go on like this one. Might want to consider this one before you brick your drive. He can easily do this one for you for a very small fee.
I see that Thatdellguy asked you where you are located. Sorry it is your drive but to change a SN is not too expensive on this one. You can brick one drive if you keep going on like this and following the suggestions of a person who does not have the tools and understand the makeup of the HDD and what they are doing. You need to understand that you are using two different HDD for Maxtor one is Poker and one is DSP this is your problem and that is why we have told you more than once if you really need this and do not understand the structure of your HDD it would be better to have someone who does change it for you. So should I have padded it at the end maybe? or FF it? The Serial Does show as what I need but program will not accept key. I have looked at the bin file with a hex editor and found the serial number location.
#Hard disk serial number changer generator mod
(I lost System 1 compatability with this mod so I just went back to my orig HHD) I have had used that in the past on a Xbox drive. Uploading and downloading firmware modules to and from the reserved area are just clickable menu options.
#Hard disk serial number changer generator professional
If your BIOS has a 128GiB/137GB HDD capacity limitation, then you could use a freeware tool such as HDAT2 or MHDD, or even HDDHackr itself, to truncate the new drive.Īs for you concerns regarding accessing the reserved area, that's what the professional tools are designed to do. For example, if your motherboard does not have a SATA port, then you could purchase a PCI SATA controller card, or you could purchase an IDE-to-SATA adapter PCB ($5 - $10). If you are concerned about the age of your hardware, then there are also several ways to circumvent any limitations. Just about any Seagate or WD drive could be modified to suit. If you opt for professional services, then once again you need not limit yourself to an identical replacement drive. Moreover, HDDHackr generates an UNDO.BIN file so that you can restore the drive to its original state should you need to do so. You don't need to do anything more than provide the BIN file. HDDHackr then uses these data to transparently modify the relevant modules in the reserved area of the WD drive. All you would need to do would be to provide a HDDSS.BIN file that incorporates your Maxtor identity data. With HDDHackr you could use a recent model WD drive with a much larger capacity, and you could do so at no cost, as many times as you like. Moreover, you are unnecessarily limiting your options. I am not to familiar with getting into these drives.
#Hard disk serial number changer generator how to
How to access the "reserved area", or if I even can. I have attached a checksum calculator written by Pete Disdale.Īnd in that is my problem. Of course these modules are located in a reserved area, not in the user area. For example, "09581F40" begins at LBA 0x0958 and has a size of 0x1F40 sectors.
#Hard disk serial number changer generator plus
I believe the file numbers reflect the starting location of the module in LBA format, plus its size in sectors. You can see that the serial number appears in 00080001.rpm and 09581F40.rpm. Here is a resource dump from a Maxtor 2B020H1 model with WAH21PB0 firmware: The two "integrity" bytes are written to the end of the block. It is computed by summing the 16-bit words in little endian format. After editing the serial numbers, you would then recalculate the checksum of each module. You would first use MRT to read all the modules, and then use a hex editor to search them for your serial number string. For example, a serial number of "B1EE47FE" would be stored as "1BEE74EF".
I don't see anything on the China HDD Union web site that would suggest that changing the serial number is a clickable procedure.Īnyway, AISI your serial number would be stored in little endian format. However, it may not be a straightforward process. Otherwise, if you insist on modifying your Maxtor drive's firmware modules, then I believe it could be done with MRT (Maxtor HDD Repair Tool, ~US$100): I can help you if you would like to try this approach.
#Hard disk serial number changer generator upgrade
That's how people circumvent Microsoft's Xbox HDD upgrade limitation. One freeware option may be to use HDDHackr to modify a recent model WD drive to identify itself with the same model number, firmware version, and serial number as your Maxtor drive.